Paper pick-uD roller assy Paper pick-up roller collars Figure 4. The user, therefore, should be fully informed about the correct storage and handling of EP-ED cartridges. Printer Media Media Load Type. Maintenance and Servicing Parts replacement schedule, list of tools, lubricants and cleaners. If blank spots occur on prints, take out the EP-ED cartridge and slowly rock it to distribute the toner evenly. Respectively for these three blocks. Dirt on power supply terminal Failure in the transfer high- voltage circuit 6 Clean the transfer roller right end bearing, the check continuity between the transfer roller power supply spring and the terminal of the high-voltage transfer unit.

Uploader: Gokasa
Date Added: 2 April 2009
File Size: 49.22 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 33706
Price: Free* [*Free Regsitration Required]

Environmental Parameters Min Operating Temperature. Brother HLe – printer – monochrome – laser Series Sign in to comment Be respectful, keep it civil and stay on topic. Do-it-all budget printer is a broter fit for tight spaces Do-it-all budget printer is a perfect fit for tight spaces by Justin Yu.

Do not disassemble the scanner unit, it can be only adjusted at the factory.

Brother HL e Toner Cartridges & Supplies

Laser beam safety is designed into the printer. Yes Check the motion of the paper-pick up block.

No Reassemble or replace the paper delivery actuator and regist sensor actuator. Advantages compared with the corona transfer method are as follows: Connector rise from OV to 5V and is the pulses having about 1 1 ms period generated at P, 7, 8 ,9 pin?

Recent Drivers  PLDS DVD - RW DH - 16ABS DRIVER

Full text of “Brother e Service Manual”

Is there already dirt on the back nrother the sheet thus removed? This residual toner is cleaned off in the drum cleaning stage so that the next print image will be clear.

The above table shows only estimated value, so these value are subject to change without prior notice. If the engine CPU detects a paper jam, the main motor, paper feed motor and scanner motor is turned off immediately and the brither status is transmitted to the video controller circuit.

The path of the beam coming through the focusing lenses is reflected by the reflective mirror.

An EP-ED cartridge used after the expiry may produce low-quality printing, so a cartridge should be used within the stated period. Paper pick-up solenoid Screw Paper pick-up solenoid Figure 4. Thermistor failure Fixing unit failure 4 Is the voltage at the pin 3 of the brlther P1 1 of the main PCB is controlled within 1.

Fixing stage Step 6 Fixing 5. Search the history of over billion web pages on the Internet. SIMM should be of pin type and its access time should be less than 70 ns.

This charging method has advantages such as lower applied voltage, less ozone generation, etc. If still remains, replace the main PCB. Dirt on power supply terminal Failure in the charging high- voltage circuit 5 Is there any dirt on the cartridge side charging terminal of the transfer unit and on the terminal of the high-voltage power supply charging unit? Appears when no cassette is set.

Recent Drivers  3C905CX DRIVER DOWNLOAD

Yes Replace the PCB having the short circuit. Appears when the cassette is set to letter 160e. If printing at dpi, you may need to add optional SIMM memory. P6 on the main PCB have the following value respectively when a sheet of paper is fed from the MP tray?

Brother HL-1660e – printer – monochrome – laser Series

If an EP-ED cartridge is unsealed soon after moved from a cold room to a warm room, condensation broyher occur inside the cartridge, which may cause broher image. No flash memory is set. Trayl paper empty sensor MP tray feed: Heat insulation cover Figure 4.

Cover Open Detect Circuit K. Adjustment lever spring pressure switching lever 2 Is the position of the adjustment lever of the cassette corresponding to the paper sheet size? No Replace the transfer base assy.